What is the difference between an office chair and a computer chair?Custom furniture manufacturers
Rirong Custom furniture manufacturers
computer chair:
1. Casters: ordinary casters, PU wheels (soft materials, suitable for wooden floors and machine rooms).
2. Chair leg: arch frame (iron frame or wooden frame): the thickness of the iron frame directly affects the service life of the chair. Surface treatment: spray paint, baking varnish (surface gloss, not easy to remove paint), electroplating (wood frame can not be electroplated), the electroplating quality is good, and it is not easy to rust. Usually the quality of the electroplating is good or not, depending on the surface polishing, the surface and the welds are polished well, the electroplating may be better. Moreover, electroplating products are not environmentally friendly. Developed countries strictly control the number of electroplating plants and the investment in environmental protection facilities.
3. Air rod: also called the extension rod, used to adjust the height and rotation of the chair. The inside of the gas rod is filled with high-pressure gas. Before the air rod was invented, the height and rotation of the chair were adjusted by the gong rod, which was eliminated because it was not humane enough to use.
4. Chassis: The part that holds up the seat, and the bottom is connected with the air rod. Many chair chassis with a retail price of less than RMB 160 do not have casings. After a long period of use, they are easy to crack and shake, and some iron plates are not thick enough. When measured with a caliper, it is only 1.7mm thick, usually 1.9mm thick. . Many of the springs of the chassis are not long enough or have no heat treatment. The heat-treated new spring has a pig liver color on the surface instead of iron.
5. Chair seat: It is composed of wood board, sponge and fabric. The quality of wood boards is usually not felt by consumers. Sponge: recycled cotton, new cotton.
6. Handrail: Thickness affects quality.
7. Seat back seat connection (corner code): The seat and the back of the chair are separated, and they are connected by steel pipe or steel plate. It is best to have a steel pipe inside the steel pipe, and only a small part has a cover. The steel plate is usually 6mm or 8mm thick. However, steel plates with a width less than 6 cm must be 8 mm thick. Otherwise it is easy to bend.
8. The material of chair back and seat: the quality evaluation method is similar, but the hardness is relatively softer. Too soft is also bad. The chair with steel frame and plastic frame is made of a combination of mesh fabric, which is breathable.
9, lumbar pillow: some chairs have, some chairs do not, the necessity depends on the comfort of the chair.
10. Headrest: Some chairs have it, some chairs don't. The necessity depends on the comfort of the chair. Adjustable function Some high-end computer chairs can adjust the height of the seat, armrest, backrest, lumbar pillow, and headrest. Low-end chairs have relatively rough surfaces.
office chair
1. The main fabric is made of high-quality breathable mesh. The mesh surface has good gloss, softness and toughness, moderate thickness, strong breathability, soft hand feel and full of toughness.
2. The backrest is designed according to ergonomics, which can reduce the discomfort of the back and back after sitting for a long time, so that the seat can reflect humanized care and modern beauty.
3. The seat cushion is made of high-density stereotyped sponge, moderately soft and hard, good resilience, no deformation, and comfortable seat feeling. The inner layer is made of molded curved wood panels that are moisture-proof, anti-corrosion, and insect-proof. The seat cushion is raised and lowered. You can lock the number of unfettered degrees.
4. The armrests are made of pu plastic, the legs of the chair are made of lacquered material, and the chair wheels are high-quality floor wheels, which move smoothly without noise and wear.
computer chair:
1. Casters: ordinary casters, PU wheels (soft materials, suitable for wooden floors and machine rooms).
2. Chair leg: arch frame (iron frame or wooden frame): the thickness of the iron frame directly affects the service life of the chair. Surface treatment: spray paint, baking varnish (surface gloss, not easy to remove paint), electroplating (wood frame can not be electroplated), the electroplating quality is good, and it is not easy to rust. Usually the quality of the electroplating is good or not, depending on the surface polishing, the surface and the welds are polished well, the electroplating may be better. Moreover, electroplating products are not environmentally friendly. Developed countries strictly control the number of electroplating plants and the investment in environmental protection facilities.
3. Air rod: also called the extension rod, used to adjust the height and rotation of the chair. The inside of the gas rod is filled with high-pressure gas. Before the air rod was invented, the height and rotation of the chair were adjusted by the gong rod, which was eliminated because it was not humane enough to use.
4. Chassis: The part that holds up the seat, and the bottom is connected with the air rod. Many chair chassis with a retail price of less than RMB 160 do not have casings. After a long period of use, they are easy to crack and shake, and some iron plates are not thick enough. When measured with a caliper, it is only 1.7mm thick, usually 1.9mm thick. . Many of the springs of the chassis are not long enough or have no heat treatment. The heat-treated new spring has a pig liver color on the surface instead of iron.
5. Chair seat: It is composed of wood board, sponge and fabric. The quality of wood boards is usually not felt by consumers. Sponge: recycled cotton, new cotton.
6. Handrail: Thickness affects quality.
7. Seat back seat connection (corner code): The seat and the back of the chair are separated, and they are connected by steel pipe or steel plate. It is best to have a steel pipe inside the steel pipe, and only a small part has a cover. The steel plate is usually 6mm or 8mm thick. However, steel plates with a width less than 6 cm must be 8 mm thick. Otherwise it is easy to bend.
8. The material of chair back and seat: the quality evaluation method is similar, but the hardness is relatively softer. Too soft is also bad. The chair with steel frame and plastic frame is made of a combination of mesh fabric, which is breathable.
9, lumbar pillow: some chairs have, some chairs do not, the necessity depends on the comfort of the chair.
10. Headrest: Some chairs have it, some chairs don't. The necessity depends on the comfort of the chair. Adjustable function Some high-end computer chairs can adjust the height of the seat, armrest, backrest, lumbar pillow, and headrest. Low-end chairs have relatively rough surfaces.
office chair
1. The main fabric is made of high-quality breathable mesh. The mesh surface has good gloss, softness and toughness, moderate thickness, strong breathability, soft hand feel and full of toughness.
2. The backrest is designed according to ergonomics, which can reduce the discomfort of the back and back after sitting for a long time, so that the seat can reflect humanized care and modern beauty.
3. The seat cushion is made of high-density stereotyped sponge, moderately soft and hard, good resilience, no deformation, and comfortable seat feeling. The inner layer is made of molded curved wood panels that are moisture-proof, anti-corrosion, and insect-proof. The seat cushion is raised and lowered. You can lock the number of unfettered degrees.
4. The armrests are made of pu plastic, the legs of the chair are made of lacquered material, and the chair wheels are high-quality floor wheels, which move smoothly without noise and wear.
Leave a comment